How do you fix error code: s1001 (network)?

Error code: S1001 is a network error that typically occurs when there is a problem with the network connection or the network itself. This error can also occur if the network is busy or if there is a problem with the network settings.

People like you are also looking for:

• plex error code: s1001 (network)
• error code: s1001 (network)

• Restart your computer
• Check your network connection
• Check your firewall settings
• Check your proxy settings
• Check your DNS settings

1. Restart your computer

1. Restart your computer.
2. Press the F8 key when your computer starts up.
3. Enter "reboot" into the computer's boot prompt.
4. Press F5 to restart your computer in the normal mode.
5. Press F9 to restart your computer in the advanced mode.
6. Press F2 to enter the BIOS.
7. Change the boot order to boot from your hard drive first.
8. Change the boot device to your CD/DVD drive.
9. Change the boot priority to your hard drive.
10. Press F10 to save your changes and exit the BIOS.
11. Press the power button to restart your computer.

2. Check your network connection

1. Check the devices that are connected to the network and verify that they are all properly set up and working.
2. Check the network connection by using a network diagnostic tool.
3. If the network connection is still not working, try to reset the network settings.

3. Check your firewall settings

1. Locate your firewall settings. This can be done by opening your firewall software, clicking on the "Firewall" tab, and looking for the "Internet Protocol Security (IPsec)" and "Windows Firewall" settings.
2. Verify that the protocol and port numbers for both the IPsec and Windows Firewall are correct. The protocol should be "TCP" and the port should be "445." The IPsec setting should be "Enabled" and the Windows Firewall setting should be "Enabled with exceptions."
3. If the protocol and port numbers are correct, verify that the "Windows Firewall" setting is set to "Block all traffic."
4. If the "Windows Firewall" setting is not set to "Block all traffic," verify that the "Windows Firewall" setting is set to "Block specific protocols."
5. Verify that the "Windows Firewall" setting is set to "Enabled."
6. If the "Windows Firewall" setting is not set to "Enabled," verify that the "Windows Firewall" setting is set to "Enabled with exceptions."
7. Verify that the "Windows Firewall" setting is set to "Enabled with exceptions."
8. Verify that the "Windows Firewall" setting is set to "Public."
9. Verify that the "Windows Firewall" setting is set to "Enabled."
10. If the "Windows Firewall" setting is not set to "Enabled," verify that the firewall software is up-to-date.

4. Check your proxy settings

1. Open your internet browser and type "proxy settings" into the address bar.
2. On the web page that appears, click on the "Configure" link in the top right corner.
3. On the "Configure Proxy Settings" page, find the section that says "Settings for network" and click on the "Advanced" link.
4. On the "Advanced Proxy Settings" page, click on the "Check proxy settings" button.
5. On the "Check Proxy Settings" page, review the proxy settings and make any necessary changes. If the proxy settings are correct, click on the "OK" button.
6. If the proxy settings are not correct, click on the "Fix Proxy Settings" button and make the necessary changes.

5. Check your DNS settings

1. Open a web browser and type "nslookup" into the address bar.
2. Type in the IP address or hostname of your device, and press Enter.
3. Type in the DNS server addresses, separated by commas, and press Enter.
4. Type in the A record for the device's IP address or hostname, and press Enter.
5. Type in the MX record for the device's IP address or hostname, and press Enter.
6. Type in the PTR record for the device's IP address or hostname, and press Enter.
7. Type in the CNAME record for the device's IP address or hostname, and press Enter.
8. Type in the NS record for the device's IP address or hostname, and press Enter.
9. Type in the MX record for the device's hostname, and press Enter.
10. Type in the PTR record for the device's hostname, and press Enter.
11. Type in the CNAME record for the device's hostname, and press Enter.
12. Type in the A record for the device's hostname, and press Enter.
13. Click OK to close the nslookup window.

If you didn't find success with an option above, then try:

1. Check your IP address.
2. Check your antivirus settings.
3. Check your router settings.
4. Check your ISP settings.
5. Try using a different browser.